Places of Usage
• It is used in load bearing surfaces, machine foundations, installation of machine assembly and under-column plates, compressor, high speed turbine, crane rails, as coating, repair, filling and horizontal crack repair material resistant to dynamic loads, friction and impact in warehouse and loading areas, in industrial floors, airports, runways and aprons, in bridge bearings. Suitable for indoor and outdoor on horizontal surfaces.
Features/ Advantages
• High resistance to chemical effects.
• It gains high strength shortly after application.
• High resistance to dynamic loads.
• It has high abrasion resistance and mechanical strength.
• Provides excellent adhesion on many dry and clean surface types.
• It is easy to mix and apply thanks to its special fillings.
• Solvent-free, eco-friendly.
Application Directions
a) Surface Preparation:
The surface should be dry, clean, sound and free of dust, oil, dirt or adhesion preventive materials should be cleaned from the surface and materials such as mortar and cement residues should be scraped. Concrete must be cured for a minimum of 28 days. The compressive strength of the concrete should be minimum 25 N/mm'. Make sure that the floor is completely dry before application. The maximum moisture content of the concrete should be 5%. All metal plates and exposed rebars that will come into contact with the material must be blasted appropriately and the surface should be primed with a suitable primer within 4 hours following this process.
b) Product Preparation:
N7007 Epoksi Ankraj, is packaged in appropriate quantities in two components. Component B (hardener) should be added to component A (epoxy resin) and mixed with 400-600 rpm drill with mixer tip for 1-2 minutes. The components were packaged in the correct mixing ratios. If a portion of the product is to be used, this rate should be observed.
c)Application Method:
The product is fluent and applied by pouring. It is shaped by spreading with trowel or spatula. In fillings to be made under large plates, casting should be made on one side and care should be taken not to create air pockets. After casting, the material should be swollen and help to evacuate the air. Due to the spreading properties of the material, Cavity around to be filled is molded. Maid edges and joints should be closed well. In order to remove the maids easily after curing, it is appropriate to cover the contacting parts with the maid release agent. The maid width on the side on which the material will be poured shall not be more than 50 mm. It is suitable to pour the material from minimum height of 150 - 200 mm for comfortable and continuous flowability. In order to ensure full contact of the material with the bottom of the base plate, the head should be kept constant during the application so that no air gap is left in between, the application should be carried out continuously if possible, and the mixture amounts must be calculated in advance.

Issues to be Considered
• Avoid applying the product at temperatures below+ 10° C and above+ 30° C.
• N7007 Epoksi Ankraj should be mixed with low speed mixing drill. Never mix with hand or trowel.
• Mix the components of N7007 Epoksi Ankraj in the correct proportions. Do not add water, solvent, etc. to the mixture externally.
• The working and curing times of epoxy resin based products depend on the ambient and floor temperature. At low temperatures, the viscosity increases, the chemical reaction slows down, thus pot life and working time prolong. At high temperatures, the opposite happens.
• Avoid application in areas that are frozen, at risk of freezing within 24 hours or exposed to direct sun and wind.
• After the application, at least 24 hours should not be touched and water contact should be prevented for 48 hours.
Cleaning of Tools:
Tools and equipment used should be cleaned with water after the application. N7007 Epoksi Ankraj can only be removed mechanically from the surface after hardening.
Security Warnings
• S2 Keep out of the reach of children.
• S24/25 Avoid contact with eyes and skin.
• S26 In contact with eye, wash with water and consult a doctor.
• S28 In contact with skin, wash immediately with plenty of water.
• S29 Do not empty into drains.
• S46 If swallowed, consult a doctor immediately and show box or label.
Storage
Store in unopened original packaging in a dry (maximum relative humidity of 60%) and cool (temperature between + 5 ° C and + 25 ° C). It should not be left in direct sunlight. Protect from frost. The mouth of the containers should be tightly closed when not in use. Shelf life is 12 months from the production date when stored in unopened original packaging in a dry (maximum 60% relative humidity) and cool(+ 5 ° C to+ 30 ° C) environment.
Consumption
The recommended amount of consumption for 1 mm thickness at 1 m'; 1,90-2, 10 kg. This value may vary depending on surface and ambient conditions.
Package   In 5 kg (A+B) set plastic buckets.