Places of Usage
• It is used primarily as a primer material on cement based screed and concrete surfaces before epoxy flooring. Used indoors, on horizontal surfaces.
Features/ Advantages
• Has low viscosity; easily penetrates the capillary gaps on the surface.
• It provides more durable and gap-free adhesion of epoxy floor coverings to the surface.
• Has high penetration ability.
• Has high adhesion strength.
• Has high mechanical resistance.
• Solvent-free, eco friendly.
Application Directions
a) Surface Preparation:
The surface must be dry, clean, sound and free of dust; oil, dirt or sticking materials must be removed from the surface; materials such as mortar, cement residues should be scraped. Prior to the application of primer on the surface, surface abrasive equipment (Shotblast, rototiger, etc.) should be used to form an open porous structure on the top layer of the application surface. Dusting should be cleaned with industrial vacuum cleaner. The corroded concrete surface should have a minimum compressive strength of 25 N/mm2 and a tensile strength of 1.5 N/mm2
• Ensure that surface moisture, relative humidity and dew point requirements are met before application.

Otherwise, the desired performance criteria from the product cannot be reached as a result of carbonation reaction on the surface. Moisture content
of the surface should be maximum 4%. Relative humidity should be maximum 80%. The dew point should be above + 3° C before and after the
application in order to prevent the formation of condensation.
New concrete structures should be allowed to dry for a minimum of 28 days. Repair of surface defects with a depth of more than 1 cm should be done with Neroflex Epoxy Repair Mortar or Neroflex Grout Mortar 6-8 hours in advance.
b) Product Preparation:
N6005 Epoksi Primer is packaged in suitable quantities in two components. Each component is first mixed in itself. Component B (Hardener) is added to component A (Epoxy resin). It is mixed with 300-400 rpm mixer tip drill for 3-4 minutes until a homogenous consistency is obtained. The entire mixture is then taken to a clean container and mixed again. If part of the product is to be used, these mixing ratios should be considered.
c)Application Method:
Prepared N6005 Epoksi Primer should be poured onto the surface and applied with a roller or trowel until a seamless layer is formed. According to the porosity of the surface, 2nd coat of 6005 Epoksi Primer should be applied. After the primer application, if the floor application of Neroflex Epoxy Self Leveling is to be made,blinding can be made with quartz or silica sand in dimensiond of 0.5 - 0.7mm.

Issues to be Considered
• Avoid application at temperatures below + 10° C and above + 30° C.
• When mixing 6005 Epoksi Primer, a suitable drill must be used, never by hand or trowel.
• Do not add water, solvent, etc. to the mixture externally. Do not thin with thinner, etc.
• Materials should be brought to the application area at least 24 hours before the application to comply with the environmental conditions.
• The working and curing times of epoxy resin based products depend on the ambient and floor temperature. Consumption amount increases as viscosity increases at low temperatures. The chemical reaction slows down, thus the pot life and working time prolongs. At high temperatures, the opposite situation is the case.
• If heating is required in the application area, only electrical, warm air blower systems should be used in order not to affect the appearance of the surface.
Cleaning of Tools:
Tools and equipment used should be cleaned with water after the application. N6005 Epoksi Primer can only be removed mechanically from the surface after hardening.
Security Warnings
• S2 Keep out of the reach of children.
• S24/25 Avoid contact with eyes and skin.
• S26 In contact with eye, wash with water and consult a doctor.
• S28 In contact with skin, wash immediately with plenty of water.
• S29 Do not empty into drains.
• S46 If swallowed, consult a doctor immediately and show box or label.
Storage
Shelf life is 12 months from date of manufacture when stored in original (unopened) package in a dry (maximum relative humidity of 60%) and cool (temperature between +5° C and + 30° q. Store in an unopened original package in a dry (maximum relative humidity of 60%) and cool (temperature between +5° C and + 30° C. It should not be left in direct sunlight.
Consumption
Primer (Less porous): 0,30 - 0,50 kg/m2
Primer (Very porous): 0, 7 -1,0 kg/m2
Package
In 24 kg (A+B) set plastic buckets.
N6005 Epoksi Primer
Quality Certificates: Manufactured according to TS EN 1504-2