Places of Usage
It is used in;
• Indoor and outdoor, • Horizontal and vertical applications,
• Hospitals and all kinds of hygienic environments,
■ Swimming pool, thermal pool and wet areas,
■ Cheese, milk, wine, meat, fish and food industries,
• Pharmaceutical, paint, paper, battery and fertilizer industries,
• Printing houses, laundries, industrial kitchens and cafeterias,
■ Places exposed to heavy pedestrian traffic such as shopping malls, terminals,
• Floor heating systems,
• Waste water and treatment plants,
• For bonding materials such as tiles, ceramics, marble, granite, acid-resistant ceramics, porcelain ceramics, glass mosaics and glass bricks to concrete, plaster and metal surfaces.
Features/ Advantages
• Does not form maid and fungus.
■ Has high mechanical strength.
• Resistant to oils, chemicals, acids, alkalis, chemical and domestic waste water.
■ Not affected by sudden temperature changes.
• Resistant to freeze-thaw cycle.
• No harmful effects on drinking water.

Application Directions
a) Surface Preparation:
If the application surface is concrete, plaster, it must be hardened and if it is metal, it must be cleaned from rust and oil. The application surface should be free of adhesive preventive materials such as dust, oil, tar, pitch, paint, silicone, curing material, detergent and molding oils. The surface should be dry, stable and level. Moisture of the surface should be below 4%.
b) Product Preparation:
N1018 Epoksifix is packaged in appropriate quantities in two components. Add 0.20 kg of component B (hardener) to 5 kg of component A (Epoxyresin) and mix for at least 3 minutes with a  400-600 rpm mixer drill with mixer bit. Component B (Hardener) is included in the package of component A (Epoxy resin). The components are packaged in the correct mixing proportions. If part of the product will be used, this rate should be observed.
c)Application Method:
N1018 Epoksifix is applied in principle as cementbased ceramic adhesives. N1018 Epoksifix is applied in a way that 2 mm thickness is obtained with suitable toothed trowel selected according to the ceramic size to be adhered. Minimum 4 mm toothed comb is used. The contact layer is formed by pressing the flat side of the trowel on the application surface where heavy load will be on and immediately the epoxy mixture is put for the application of the toothed trowel, applied with a comb and ceramics are bonded. Do not bond to the product that has started to dry. Joint filling application is started after 1 day.

Issues to be Considered
• Avoid application the product at temperatures below+ 1 o0 c and above+ 20° C.
• N1018 Epoksifix should be mixed with a suitable mixing drill. Never mix with hand or trowel.
• The components of N1018 Epoksifix should be mixed in the correct proportions. Do not add water, solvent, etc. to the mixture externally.
• Working and hardening times of epoxy resin based products depend on the ambient and floor temperature. Consumption amount increases as viscosity increases at low temperatures. The chemical reaction slows down, thus the pot life and working time prolongs. At high temperatures, the reverse situation happens.
• Avoid application in areas that are frozen, at risk of freezing within 24 hours or exposed to direct sun and wind.
• After the application, it should not be touched for at least 24 hours and water contact should be prevented for 48 hour.
Cleaning of Tools:
Tools and equipment used should be cleaned with water after the application. 1018 Epoksifix can only be removed mechanically from the surface after hardening.
Security Warnings
• S2 Keep out of the reach of children.
• S24/25 Avoid contact with eyes and skin.
• S26 In contact with eye, wash with water and consult a doctor.
• S28 In contact with skin, wash immediately with plenty of water.
• S29 Do not empty into drains.
• S46 If swallowed, consult a doctor immediately and show box or label.
Storage
It should be stored in unopened original package in a cool and dry environment by protecting from frost. For short-term storage, maximum 3 pallets should be placed over and over and the shipment should be made with first in first out system. For long-term storage, pallets should not be placed over and over. It can be stored for 12 months from the date of production if proper storage conditions are met. Opened packages should be kept tightly closed and stored under proper storage conditions and should be used within one week.
Consumption
Average 4-5 kg/m'
Package
With 2 component
a) 1 8 kg plastic bucket
b) 3 kg plastic bucket
N1018 Epoksifix
Quality Certificates:
Manufactured according to TS EN 1 504-6
R : Reaction resin based
2 : High performance
T : Reduced slip property
E : Prolonged working time