Places of Usage:
It gives excellent results;
• Horizontal and vertical applications in indoor and outdoor,
• Bonding of ceramic, granite, marble, porcelain, natural stone, glass mosaic and pressed bricks to cement based surfaces subject to temperature differences,
• After priming the surfaces affected by temperature changes such as gypsum-plaster board, gypsum-plaster, heat-gas concrete with Neroflex Plaster , bonding of ceramic, granite, marble, natural stone and glass mosaic on it,
• In wet areas such as swimming pools, water tanks, bathrooms, etc, floor heating floors, heated pools, thermal pools, swimming pools where water is not drained in winter,
•Walland floor coverings of cold storage depots,
• In ceramic and granite bonding works on the facades of buildings, renovation and repair works, and ceramic bonding works on ceramics.

Features/ Advantages:
• Has quick setting feature.
• Has long penetrating time.
• Easy to prepare and apply.
• Does not slip in vertical applications.
• Resistant to freeze-thaw cycle.
• Resistant to stress and vibration caused by temperature differences.

Application Directions:
a) Surface Preparation:
Take care that the application surface should be solid, dry, carrier, dust-free and clean and at the same time in balance. The surface should be thoroughly cleaned of all kinds of oil, grease, rust and paraffin residues that will weaken the adherence and there should be no loose particles on the surface. Damaged surfaces with a depth of 5 to 20 mm should be repaired with Neroflex Repair Mortars two days in advance. If the temperature of the surface to be applied is above+ 25° C, the surface should be moistened.
On Plaster Based Surfaces, Plaster is applied on gypsum-paper board, gypsum-plaster, gas concrete, lime stuff and chipboard with high absorbency. Adhesion can be started 5 minutes after the primer application. Wood particleboards surfaces (OSB and Chipboards), Wood particleboards
should contain a maximum moisture content of 10%. Wood particleboard (V100) applied to the floors should be minimum 25mm and 19mm for the walls. The boards should be screwed to the surface at 30 cm intervals. The edge joint must be at least 8mm wide. At the joints of the chips, grooves should be opened and filled with Joint Sealant. Wood paperboards should be primed with Neroflex Plaster in dry environments. If the boards are in place that exposed to moisture (exterior), it is applied with Fully Flexible Waterproofing Material in two layers and mesh reinforced.
b) Product Preparation:
The water in appropriate amount is poured into the clean mixing vessel with a scale. N1021 Technofast is added slowly and mixed with a 400-600 rpm mixer for 3-5 minutes until a uniform and lump-free mixture is obtained. After resting for 3-5 minutes and mixing again for 30 seconds, the material is ready for use.
c)Application Method:
N1021 Technofast layer of 1 mm thickness is applied to the application surface with the flat side of the trowel. 1021 Technofast is applied in one direction in such a way that a uniform thickness is obtained with the toothed side of the trowel to an area that can be covered within 30 minutes, open waiting time. For the bonding of tiles or ceramics with different thicknesses, it is recommended to apply 1 mm thick mortar under each tile or ceramic in order to cover the defects on the application surface. When applying tiles or ceramics in place, the tiles or ceramics are floated in the mortar to ensure that the N1021 Technofast is fully in contact. Application is completed by leaving the recommended joint gap according to the appropriate tile or ceramic size. Neroflex Joint Fillings should be used to fill the leh joint gaps. Joints can be applied after approximately 24 hours.

Issues to be Considered:
• Avoid application at temperatures below +5°C and above +35°C.
• Pay attention to the amount of water added to the mortar. Do not add more water than necessary.
• Avoid application in areas that are frozen, at risk of freezing within 24 hours or exposed to direct sun and wind.

Cleaning of Tools:                                                                  Tools and equipment used should be cleaned with water aher the application. N1021 Technofast can only be removed mechanically from the surface after hardening.

Security Warnings:
• S2 Keep out of the reach of children.
• S24/25 Avoid contact with eyes and skin.
• S26 In contact with eye, wash with water and consult a doctor.
• S28 In contact with skin, wash immediately with plenty of water.
• S29 Do not empty into drains.
• S46 If swallowed, consult a doctor immediately and show box or label.

Consumption: Average 4-5 kg/m2
Package: In 20 kg krah bags. 

N1021 TECHNOFAST C2FTE S1                                                                                                                                                                                                     QUALITY CERTIFICATES:
Manufactured according to TS EN 12004.
C :Cement based
1 : Normal hardening (Standard performance)
F : Quick setting
T: Reduced slip property
E: Prolonged working time