Places of Usage
•Tunnels
• Foundations
• Culverts
• Channels
• Water tanks
• Check galleries
• Manholes
• Swimming pools

Features/ Advantages
• Ready to use and.
• Economical insulation.
• Does not affect the setting time and strength of the mortar.

Application Directions
a) Surface Preparation:
Concrete surfaces should be roughened or notched by using methods such as abrasion with wire, sandblasting method and any accessories, fittings etc. equipments on the surface should be removed. The surface should be improved by removing cracks, porous areas and blistering from the surface. Water leaks must be stopped or the water level reduced by the Quick Set Water Impermeability Additive. A slurry consistency primer layer should be applied before the first coat application.
b) Product Preparation:
Shake the product before use. Mix 1 scale of N3015 Sikalem thoroughly with 10 scales of clean water in a clean container. For better results, it is recommended to first mix the water with an equal amount of N3015 Sikalem and then add the rest of the water.

c)Application Method:
Walls: Apply a mixed mortar with a steel trowel to a thickness of 6 mm until a smooth consistency is achieved. Apply the second coat after the first coat begins to cure (usually 4-5 hours).After second coat application, if four coats are to be applied, after application of the third coat, apply only a 'thin' mortar layer prepared with water to increase the adhesion of the top coat. In order to obtain better adhesion strengths, intermediate coats should not be scraped for roughening purpose. Topcoat application should be done with a wooden trowel to avoid the formation of grout residues on the surface.
First coat (1 : 1 ): The dry mix should contain the same amounts of cement and sand (passing
through a 3 mm sieve) by volume. N3015 Sikalem mixture is then added and mixed.                  Second coat (1 : 1,5): Prepare cement:sand mixture in 1 :1,5 rate (passing through a 3 mm sieve) and add N3015 Sikalem mixture.
Third coat (1 : 2,5): The dry mixture ratio should be 1: 2.5 (cement: sand. Add N3015 Sikalem mixture and mix.
Topcoat (1 : 1) (on the second or third coat): The dry mixture should contain 1: 1 (by volume) of cement: sand and the mortar produced without adding 3015 Sikalem should be applied with a wooden trowel. For best results, the cement should be fresh Portland cement. Sand; clean, angular and less than 3 mm in size. Soft and round grained sands are not useful.
Floors: The application which is normally done together with primer (Water, Latex, sand, cement) application with two coats of brush is as follows; Adhesive coat (1 : 1): Dry mix cement and sand, N3015 Sikalem mixture is added and then mix until a plastic consistency is obtained.
Main floor coat (1 : 2,5): Spread the mixture in a semi-dry state over the still wet adhesive layer, not thinner than 28 mm, and ram until moisture rises to the surface. Smooth the surface with a wooden trowel.

Issues to be Considered
• Junction Points: Particular attention should be paid to all junctions in the applied area. Each layer should be produced by retracting 10 cm from the previous floor.
• Corners (Wall-Floor Joints): The first and second layers of the wall plasters should turn on the floor by 200 mm and 100 mm respectively and then the application should be completed as described in
the 'Joint Points' section.

Cleaning of Tools:
Tools and equipment used should be cleaned with water after the application. N3015 Sikalem can only be removed mechanically from the surface after hardening.

Security Warnings
• S2 Keep out of the reach of children.
• S24/25 Avoid contact with eyes and skin.
• S26 In contact with eye, wash with water and consult a doctor.
• S28 In contact with skin, wash immediately with plenty of water.
• S29 Do not empty into drains.
• S46 If swallowed, consult a doctor immediately and show box or label.

Storage
It should be stored in unopened original package in a cool and dry environment by protecting from frost. For short-term storage, maximum 3 pallets should be placed over and over and the shipment should be made with first in first out system. For long-term storage, pallets should not be placed over and over. It can be stored for 12 months from the date of production if proper storage conditions
are met. Opened packages should be kept tightly closed and stored under proper storage conditions and should be used within one week.

Consumption
N3015 Sikalem is added to clean mixture water for use. The ratio of water is normally 1: 10, corresponding to approximately 3% of binder weight. If very wet sand is used, this ratio should be increased up to 1: 8 or even 1: 6.

Package
In 30 It and 5 It plastic jerrycans.
N3015 Sikalem
Quality Certificates:
Manufactured according to TSEK