Places of Usage
• Indoors-outdoors, vertical and horizontal applications from the direction of water,
• In basic insulation,
• In retaining walls,
• On floors that are thought to make deflection,
• On terraces (can be used under light load without protection.)
• In wet areas such as WC, bathroom, kitchen and balcony,
• In swimming pools,
• In drinking and utility water tanks,
• In facilities such as hot springs and Turkish baths,
• In sea water channels,
• Where waterproofing and protection against salty water is required,
• Protection of concrete surfaces against carbonation and chlorine attacks,
• Walking paths of marinas,
• For insulation of flower heads.
• In areas where UV resistance is required.

Features/ Advantages
• N3009-02 Elastico Plus UV 2K with a thickness of 1 mm provides equivalent protection to concrete over 80 cm against carbonation.
• Waterproof, resistant to positive water pressure of 7 bar.
• Has excellent adhesion properties.
• Easy to prepare and apply.
• It is applied with brush and spraying machine.
• Long working time.
• Resistant to UV rays.
• Suitable for light pedestrian traffic.
• Water vapor permeable.
• High durability.
• Resistant to freeze-thaw cycle.
• High resistance to carbon dioxide and chlorine ions.
• While a curing time of 7-28 days is required for conventional waterproofing materials, it can be applied to a fresh concrete of 24 hours.
• It can be used safely in drinking water tanks.

Application Directions
a) Surface Preparation:
It should be ensured that the cement-based surfaces in contact with water are solid, dry, carrier, dust-free and clean and at the same time in balance. The surface should be thoroughly cleaned of any oil, grease, rust and paraffin residues that may weaken the adherence and there should be no loose particles on the surface. Iron and wooden wedges on the surface should be removed and if any, active water leakages and gaps should be filled with Neroflex Sealant Mortar or Structural Repair Mortar, and corners and edges should be chamfered at least 4 cm radius. Application surface is wet and wait until the application surface is wet and dry/wet. If the coating material loses water immediately and becomes matt, it is understood that the surface is not sufficiently wetted or dries quickly. In such cases, when the air is hot or the materials remain in the wind, only 10% of component B can be added to the mixed material for the first layer.
b) Product Preparation:
Liquid component B (N3009-02 Elastico Plus UV 2K) is poured into a clean application bucket and powder component A (N3009-02 Elastico Plus UV 2K) is added slowly and they are mixed with a 400-600 rpm mixer for 3-5 minutes until a homogenous and lump-free mixture is obtained. After resting for 3-5 minutes and mixing again for  30 seconds, the material is ready for use.
c)Application Method:
Prepared N3009-02 Elastico Plus UV 2K mixture is applied in two or three layers with the help of a Thora brush. The direction of brush application on each layer should be perpendicular to each other. Waiting time between coats varies according to ambient conditions.

Issues to be Considered
• Avoid application at temperatures below + 5°C and above+ 35°C.
• Avoid application in areas that are frozen, at risk of freezing within 24 hours or exposed to direct sun and wind.
• Do not add water to the mixture externally.
• Always powder component should be added to the liquid component.
• The wet film thickness during application should not exceed 2 mm for one coat.

Cleaning of Tools: Tools and equipment used should be cleaned with water after the application. N3009-02 Elastico UV 2K can only be removed mechanically from the surface after hardening.

Security Warnings:
• S2 Keep out of the reach of children.
• S24/25 Avoid contact with eyes and skin.
• S26 In contact with eye, wash with water and consult a doctor.
• S28 In contact with skin, wash immediately with plenty of water.
• S29 Do not empty into drains.
• S46 If swallowed, consult a doctor immediately and show box or label.

Storage:
It should be stored in unopened original package in a cool and dry environment by protecting from frost. For short-term storage, maximum 3 palletsshould be placed over and over and the shipment
should be made with first in first out system. For long-term storage, pallets should not be placed over and over. It can be stored for 12 months from the date of production if proper storage conditions are met. Opened packages should be kept tightly closed and stored under proper storage conditions and should be used within one week.

Consumption:
First layer consumption: 1,50 kg/m2 mixture
Second layer consumption: 1,50 kg/m2 mixture
Third layer consumption: 1,00 kg/m2 mixture

Package:
Component A: In 20 kg kraft bags.
Component B: In 10 It plastic jerrycans.
N3009-02 Elastico Plus UV 2K
Quality Certificates:
Manufactured according to TS EN 1504-2