Places of Usage:
It is used;
• Waterproofing of horizontal and vertical surfaces,
• Waterproofing from negative or positive side,
• For waterproofing of underground and above ground structures,
• Waterproofing of concrete, plaster and screed.

Features/ Advantages:
• Easy to prepare and apply.
• It is applied with a brush.
• N3001 Kristalize Plus fills capillary gaps with permanent Qnsoluble) crystals formed by it and provides water impermeability.
• Protects concrete and reinforcement from corrosive effects of water.
• Resistant to negative and positive water pressure.
• Water vapor permeable.
• Resistant to freeze-thaw cycle.
• The crystals formed by mortar do not dissolve, not leave from surface and not aging.

Application Directions:
a) Surface Preparation:
The application surfaces must be moist and dry surfaces should be moistened before application. Humidification is performed 24 hours before application and again 2 hours before the surface is fully saturated with water. Care should be taken not to accumulate water on the surfaces. Surfaces must be clean, sound, carrier and free from free particles. Layers such as oil, grease, dirt, paint, cement slurry, rust, molding oil, salt effiorescense that reduce adherence should be thoroughly cleaned before application.The surfaces should be
roughened by mechanical methods in the required areas. Surfaces to be applied should be free of pits, fractures, segregation, maid defects, cracks, be smooth and not have dust emission. Such defects should be corrected with a repair mortar consisting of Neroflex Repair Mortar and Neroflex Latex mixture before application. Dilatations should be elastically insulated with Flex Band.
b) Product Preparation:
8.0 -8.S liters of clean water is prepared in a suitable pot. N3001 Kristalize Plus (25 kg) is added by continuous mixing. Mixing is continued for approximately 3 minutes. Mixing must be done with the help of a low speed (400 rpm) mixer and mixer tip. As a result of mixing, a homogenous, lump-free and spreadable mortar is obtained.
c) Application Method:
N3001 Kristalize Plus is applied with a brush or suitable spraying equipment. Application is done in 2 or 3 layers. Layers should be applied homogeneously and uniformly, application should be done in the same direction on each layer. Avoid random and irregular applications. Allow to dry between layers ( Minimum 3 hours ) but no longer than 24 hours. The surface should be cured by moistening at intervals during 72 hours following the application. It is important that cure application is performed correctly and adequately, humidification should be done regularly and frequently.

Issues to be Considered:
• Avoid application at temperatures below +5° C and above+ 35° C.
• Avoid application in areas that are frozen, at risk of freezing within 24 hours or exposed to direct sun and wind.
• Never add powder and water to the mortar that has expired. Mix frequently to maintain the consistency of the mortar during application.
• Since water pressure accelerates crystal formation and penetration of N3001 Kristalize Plus into concrete, structures such as water tanks should be filled with water 24 hours after the application of top coat N3001 Kristalize Plus. Complete waterproofing is usually achieved after a period of 5-7 days after application. Earth fill is done at the end of this period.
• The crystal formation and penetration degree depends on the density of the concrete and the absorbency
of the surface.
• Crystals formed by N3001 Kristalize Plus may create a very non-decorative appearance. To prevent this, while top coat of N3001 Kristalize Plus is stil wet, plaster should be applied on it and paint should be applied on the plaster. If ceramic or tile application will be made, ceramic adhesive should be applied directly on the freshly applied N3001 Kristalize Plus. If these applications will be applied on cured N3001 Kristalize Plus, the crystals on the surface should be wiped with diluted hydrochloric acid or bleach, then plaster should be applied on it. This wiping only destroys the crystals on the surface, does not damage the crystals penetrated into the concrete.

Cleaning of Tools:
Tools and equipment used should be cleaned with water after the application. N3001 Kristalize Plus can only be removed mechanically from the surface after hardening.

Security Warnings:
• S2 Keep out of the reach of children.
• S24/25 Avoid contact with eyes and skin.
• S26 In contact with eye, wash with water and consult a doctor.
• S28 In contact with skin, wash immediately with plenty of water.
• S29 Do not empty into drains.
• S4 6 If swallowed, consult a doctor immediately and show box or label.

Consumption:
Against moisture (at 2 layers) 1,0 kg/ m2
Against unpressurized water (at 2 layers) 1, 5 kg/ m2
Against pressurized water (at 2 -3 layers) 2,0 kg/ m2

Package:   25 kg kraft bags. 

N3001 Kristalize Plus
Quality Certificates:
Manufactured according to TS EN 1 504-2