Places of Usage
• Used indoors and outdoors on lined concrete and lined gas concrete surfaces, walls and ceilings where all kinds of rough plaster is applied.

Features I Advantages
• Provides a smooth surface.
• As it is white color, it can be used without paint.
• It has a positive effect on the overall appearance of the building.
• Reduces paint consumption.
• Saves time and labor.
• As it provides high adherence with the surface, provide an application that has less loss of fall back than black plaster.
• It provides high adherence and stability, does not sag.
• As it is a fabricated mortar, it provides quality continuity compared to black plaster.
• It is more resistant to outdoor conditions than black plaster.

Application Directions
a) Surface Preparation:
The surface should be dry, clean, sound and free of dust, oil, dirt or adhesion preventive materials should be cleaned from the surface and materials such as mortar and cement residues should be scraped. Repair of surface defects with a depth of more than 1 cm should be done with Neroflex Repair Mortars 6-8 hours before application. In cases where structural repair mortar is required, Neroflex Structural Repair Mortars should be preferred. Application surface should be moistened with water if necessary. After the surface cleaning, the surface should be primed with Neroflex Multipurpose Primer as one coat and allowed to dry for 1-2 hours in order to increase the adhesion strength and balance the surface absorbency. Before applying the gas concrete surfaces, the water absorbency of the surface should be reduced by applying Neroflex Multipurpose Primer. In order to increase the adhesion strength before the application on exposed concrete surfaces, the surface should be primed with Neroflex Exposed Concrete Primer as a single coat and allowed to dry for a minimum of3 hours.
b) Product Preparation:
35 kg Neroflex Finish Plaster (Gray-White) is added into approximately 8-9 liters of clean water and mixed with a low-speed mixer so that no lumps remain. The prepared mortar is left to mature for 5-1 0 minutes and used by mixing again for 1-2 minutes. The mixture in the container should be consumed within 2-3 hours.
c) Application Method:
After the application is done with a steel trowel, the surface should be smoothed with a gauge. Application thickness should be between 2 mm and 7 mm. After the plaster is discharged its water, the surface should be clovered and the final corrections should be made with a damp sponge.

Issues to be Considered
■ Avoid application at temperatures below +5° C and above+3 S0 C.
• Do not add foreign materials such as lime, cement, sand and gypsum into the material.
• Pay attention to the amount of water added to the mortar. Do not add more water than necessary.
• Avoid application in areas that are frozen, at risk of freezing within 24 hours or exposed to direct sun and wind. If snowfall or severe cold is expected within about one week after application, no application should be performed or protection measures should be taken.
• Never add water and powder to the mortar that has expired.

Cleaning of Tools:
Tools and equipment used should be cleaned with water after the application. N5001 PLASTER Art ES can only be removed mechanically from the surface after hardening.

Security Warnings
• S2 Keep out of the reach of children.
• S24/25 Avoid contact with eyes and skin.
• S26 In contact with eye, wash with water and consult a doctor.
• S28 In contact with skin, wash immediately with plenty of water.
• S29 Do not empty into drains.
• S46 If swallowed, consult a doctor immediately and show box or label.

Storage
It should be stored in unopened original package in a cool and dry environment by protecting from frost. For short-term storage, maximum 3 pallets should be placed over and over and the shipment should be made with first in first out system. For long-term storage, pallets should not be placed over and over. It can be stored for 12 months from the date of production if proper storage conditions are met. Opened packages should be kept tightly closed and stored under proper storage conditions and should be used within one week.

Consumption
The recommended amount of consumption for 1 mm thickness at 1 m2
-(Thin) On gas concrete surface: 1,5 - 2,5 kg
- On primed concrete surface: 2,0-3,0 kg
- Rough plastered surface: 2,0 -3,0 kg.
-(Thick) On gas concrete surface: 15,0-16,0 kg
- On primed concrete surface: 17,0-18,0 kg
- On the briquette surface: 17,5-18,5 kg.
- On the brick surface: 20,5 -21,5 kg.
This value may vary depending on surface and ambient conditions.

Package 35 kg kraft bags. 
N5001 PLASTER Art ES
Quality Certificates:
Manufactured according to TS EN 998-1 (GP)